How to thicken vocals with short, high-density reverb?

Thickening vocals with short high-density reverb has been a strategy of music production and performance for literally thousands of years.

It’s the reason opera houses were designed to be a particular size, and why we sound better when singing in the shower than in large rooms.
When vocals are either recorded or processed using this technique they will have quick reflections that blend into it making them thicker sounding.

The simplest way of adding a thicker sound to vocals is with short, high-density reverb.

This can be achieved by choosing an ambient or room setting on the reverb plugin and adjusting the RT60 accordingly:
Short for bright sounds and tight vocal enunciation; moderate for more realistic sounding effects.
For even better results you could combine multiple reverbs together!

Related questions to How to thicken vocals with short, high-density reverb?

How to clean up your vocal low-end?

When it comes down to vocals, the lower frequencies are important because they can both enhance and hinder.
For 100Hz+, these will provide power and body in your mix.

But anything below that frequency is going have an adverse effect on what’s happening with those aforementioned qualities – plus there’ll be noticeable plosives or microphone rumble (especially if you’re using a condenser). These things are going cause overall issues for not only yourself but also everyone else who has part of their sound coming from you as well!

This is a great guide on how to clean up your vocals!

To start, you should use an EQ and cut the frequency range of 100Hz.
This will reduce any unwanted noise in the lower end spectrum such as background interference or amplified frequencies from other sources like instruments that are playing at similar levels. Additionally, using natural phase options can help eliminate some problems with phasing if there’s too much cancellation going on when it interacts with another instrument played higher than this vocal track for instance.

How to de-emphasize vocal frequencies before compression?

To de-emphasize vocal frequencies before compression, you can use a parametric or low pass filter to remove the frequency range from your signal.
This will make the compressor less likely to affect that particular part of the spectrum and add its timbre – which is usually desirable when using it as an effect in itself – while also making any other EQs after more effective because they won’t be cutting out these areas.

For example, say I don’t want significant amount of compression occurring at 2kHz–or in other words, I don’t want my voice’s tonal quality affected by this type of distortion–I could cut this area with a parametric filter beforehand so it isn’t included within my sound source.

The vocal range that you want to emphasize is the one before it gets compressed.
You would use an EQ to emphasize this frequency, then compress your vocals accordingly. If reducing these frequencies made them sound unbalanced, a second EQ should be used after the compressor so they can add back in those tones into their original position.

How to emphasize vocal frequencies before compression?

What is the best way to emphasize vocal frequencies before compression?
If you want a particular frequency or set of frequencies to be compressed slightly hard than others, you can use an EQ before your compressor.
This will create a very unique tone that wouldn’t have been able to achieved otherwise!

For example, I may want to boost 2kHz in order add clarity and more sharpness into my vocals; these boosted ranges should then be heavily compressed for balance purposes which would result in increased coloration as well.

To make a song sound more powerful you can apply an effect called pre-emphasis.
This is achieved by boosting frequencies before the vocals get compressed, causing them to stand out when it comes time for mastering or converting your track into mp3 format.

Once again keep in mind that this will not have much of an impact on lower quality recordings so don’t waste time with high resolutions if they are too low fidelity already.”

How to use a limiter on vocals?

A limiter is a powerful tool that can help you control dynamics without introducing unwanted distortion.
When using compression to tame vocals, it may sometimes be necessary for the compressor to introduce some level of saturation in order do its job effectively and keep up with all your vocal’s harmonics.

Since this would increase the amount of noise within your track, one option might be use a limiter instead; as limiters are designed specifically take care of high frequencies (20- 20Khz), they’re more suited for addressing artifacts caused by aggressive compression while still retaining cleanliness.

Limiting vocals is a delicate art.
There are different types of limiting, and it’s important to know which one you’re using in order for your vocalist not to be pushed too far into the mix or become under-powered when their song mixes with other instruments.

If you want an intense effect on the level threshold, then try setting up an L2 like this: set the mode switch (the top left button) at “Modern,” turn off Auto Gain Compensation by clicking that same button again so there’ll never be any clipping distortion; adjust Threshold until all peaks seem linear; raise Output Level as desired without going over 0dBFS Max Limit!

How to use compressors with vocal algorithms?

There are many different ways to compress vocals in the studio.
Some people prefer a more manual approach, while others want something that is already programmed for them and offers presets tailored specifically towards their vocal sound.
FabFilter Pro-C2 has a great set of algorithms designed from top to bottom with lead vocals and background vox in mind – which will provide you with some good starting points depending on your output needs!

The Softube Drawmer S73 also features an automatic knee setting as well as an auto ratio function – this changes based on what type of input it receives so if you’re looking for something straightforward then these might be two perfect options to look into next time around!

Ever wondered how to use compressors with vocal algorithms?
It’s actually pretty easy. All you need is a compressor and the right settings for it!

One of my favorite ways that I like to utilize one when mixing vocals, especially when there are too many people singing at once in order to make them stand out more than they would otherwise be able.

How to de-ess vocals with compression?

If you’re looking to de-ess vocals in a more complex way than your typically de-essing, then compression might be the answer.
Compression can help reduce sibilance by boosting certain frequencies and lowering others.
This is done with an internal sidechain option which some compressors offer – like Fabfilter Pro C 2 or Weiss DS1 MK3 for example.

Compressing vocals can be tricky because you have to know what frequency range the sibilance is in.
Generally, it’s 5-10kHz but could vary between 4 and 12 kHz depending on who’s singing or how much they’re screaming into a microphone.

One way to isolate just the high frequencies would be by using an internal sidechain (a filter that only takes audio input from inside of its own plugin).
Once isolated with compression as needed, this should help diminish any unpleasant hissing sounds caused when speaking words like ‘s’ or ’t’.

How to squeeze vocals with opto and soft-knee compression?

How do I squeeze vocals with optical and soft-knee compression?

Optical compression is a great way to recreate the sound of an old tape recorder.
It’s perfect for squeezing up your vocal, as well since it has that gradual but noticeable effect on volume levels.

To achieve this yourself, start by choosing various settings for your compressor – then create a soft-knee setting and lower the threshold until you’re achieving around 8dB worth of compression.

Compression can be used to make vocals more dynamic and vibrant. Opto, or optical compression works by using a light-sensitive resistor which is gradually reduced when the input signal becomes louder than its set threshold level.

Soft-knee compression does not have this exponential effect on your signal’s gain as it approaches its maximum limit like opto; instead there will always just be some degree of amount applied at any time no matter what volume you’re playing at really (although still fairly gradual).

The ratio for these compressors should ideally fall between 2:1 and 4:1 depending on how much control one wants over their sound in terms of dynamics range – less control means that softer parts are compressed slightly whereas with higher ratios they would get.

How to control vocals with advanced compression?

One way to control the vocals in your song is with advanced compression.

Start by setting a 5:1 ratio, and selecting an attack time of 0ms – this will ensure that all dynamics are being compressed.
Increase input volume by about 3 dB while simultaneously reducing output levels by similar degrees (adjusting so as not to exceed maximum peak).

This should drive the vocal into the compressor without overloading it- or you can use these settings for other aspects of your mix like drums or bass lines too!

Have you ever wanted to control your vocals? Well, with advanced compression, that is possible.
First of all, use a medium-length release around 300 milliseconds – this will hold onto the vocal for long enough to control it without losing its intelligibility.

How to thicken vocals with low-level compression?

I love to use low-level compression for adding detail and thickening any instrument.
It brings up quieter details while reducing the dynamic range, which increases amplitude.

This works similarly to saturation but instead of generating harmonics, it amplifies existing signals (if this plugin is used sparingly).
I’ll reduce depth on OTT by Xfer records when I’m using this so that there’s a minimal amount of downward compression with 0% set as an option in case you need more control over your levels after applying these changes.

Using compression can be a useful strategy for thickening vocals.
In this article, we’ll show you how to use low-level compression in Audacity & detail the process of dragging bars and amplifying the lows slightly since it will help make or thin vocals sound thicker.

How to thicken vocals with inverse equalization?

Thicken vocals with inverse equalization? Inverse EQ is a process of matching the frequency response to another signal via an external side chain.
It can be great at indirectly thickening vocals and will make your vocal cut through a mix.

One way you can do this, for example, is by mixing in instrumental music full blast on one channel while recording yourself singing along (you’ll need headphones).
Delete any bands below 80Hz or above 15kHz that are not found within the instrumental song’s range.

There are a few methods for thickening vocal tracks with inverse equalization.

First, highlight all the bands and invert the gain of each band to achieve an amplified low-frequency effect but be sure you do this subtly because too much can leave your vocals sounding muddy or cause distortion over time.

You will also want to use linear phase mode so that there is no excessive phasing from multiple frequencies needed for thicken up effects.

How to thicken vocals with dynamic equalization?

Dynamic equalization is a great way at adding some natural-sounding dynamics into your vocal – if used for lower frequencies, it’s very effective at thickening the sound of either a sung or spoken vocal.

I like to amplify and expand 200Hz on my vocals if they need that extra power.
If you do choose to use this method, I recommend trying it with Pro-Q 3 because not only does this plugin offer low latency linear phase mode but also offers up so many other options which are perfect for boosting any frequency without changing its signal’s phase in ways that might cause feedback issues when recording live instruments.”

Dynamic EQ is a great tool for thickening vocals, but you don’t have to stop there.
You can also take the Tokyo Dawn Labs NOVA out of your producer’s kit bag and see if it fits!

This powerful equalizer provides an easy way to adjust specific frequencies in order to change how they sound.
It has presets that are designed specifically for vocal tracks which will make them stand out more or add some thickness without being too heavy-handed with effects processing.
Give the free plugin a try next time you’re stuck on dynamic eq alone!

How to thicken vocals with opto compression?

Optical compression is a really interesting and unique form of compression – in the hardware, it utilizes a light sensor that determines when it begins to compress your vocals.
This results in an effect which behaves very differently than most FET or digital compressor effects would on them.

Because of this behavior, optical compression can be used for thickening vocal tracks – something you might have heard before with bass guitars but has similar softening properties to make instrumentals sound fuller too!

As a singer, have you ever wondered how to make your vocals sound thicker with an optical compressor?

Optocompression may not work out for every vocalist but it provides the perfect classic warm tone and can give great versatility.

How to thicken vocals with saturation?

Saturation is a combination of soft-knee compression and harmonic distortion – it gradually compresses the signal which controls its dynamics while simultaneously adding in harmonics that raise the overall amplitude.
Because of this combo, saturation is a perfect form for thickening your vocal performance because it creates strong second order harmonic that doubles up on fundamental frequency.

Just about any saturator will work well for this but tube based sound processing may be one to consider as they are more likely than most other types to add an extra layer or two worth of sonic depth by reinforcing higher frequencies through mid/high gain ranges.

If you want to thicken your vocals, saturation is a good option.

It gradually compresses the signal for control of dynamics while simultaneously adding in harmonics that rise overall amplitude- perfect combo!

To get tube-based results, try saturating with any type of pedal or plugin and see what sounds best for you.

How to thicken vocals with short delay?

How to thicken vocals with short delay? Similar to short reverbs, it can be a great idea for thickening your sound.
This technique was first used in the 50s by using multiple tape heads and creating what’s called slapback delays which is still effective today if you want an older sound.

The same concept carries over today but instead of tapes or analog equipment, digital processors will do the job just fine so long as they are below 130ms – that creates 3-5 voices we perceive coming from 1 source (so please don’t make them too high)!

There are many ways to thicken vocals, but one of the most effective ones is with short delay.

For whatever reason, if the delay is greater than 130 milliseconds we perceive it as coming from two or more sources and this can create a thin sounding effect that isn’t cohesive enough for our ears.
So keep your delays below 130ms in order to have them sound thick and coherent like they’re coming out of just one source!

What frequency are vocals?

What frequency is a vocal?

The fundamental frequencies of male vocals are usually between 100–300 Hz, while the fundamentals for female voices fall more around 200-400Hz. The human voice has been said to have an emotional range that can be up from 9 octaves and down from 1/2 step depending on how much breath support you use with your harmonics.

How to EQ a vocal bus?

Equalizing vocals is time-consuming. You’ll need to consider the background vocals, and effects as well in order to get a nice balance of frequencies for all 4 channels on your vocal bus. This will be different from equalizing an individual voice since there are more elements that you’ll have to take into account such as stereo imaging which can sometimes make it difficult depending on what type of plugin or processing gear you use.

A lot of engineers want to have small control over the tone and balance of their vocals. For this, it is recommended that they use an equalizer with both sides being mid-side EQs. This way you can make adjustments on either side without affecting other frequencies in your song as much due to phase cancellation from mixing stereo signals together too close.

I recommend using one low pass filter for every piece or group, so there are no overlapping frequencies happening between similar tracks such as guitars and basses when recording multiple instruments simultaneously.

How to add air to your vocal?

In order to achieve a professional voice, it’s important that you get air in your vocal. All you need is an EQ shelf filter at 12kHz and up with subtle amplification of this range until you’re happy. You’ll find some EQs go as high as 40 kHz but don’t worry about going too high because we can’t hear anything past 20 or 25 kHz anyway, so these will work well for us!

You’ll want to make sure you’re using a higher sampling rate for your session if you plan on amplifying frequencies above 25kHz. If, for example, the max frequency supported by your audio device is 44.1 kHz, and it’s trying to amplify an input of 25 KHz (which would be amplified as 22050 Hz), then any sounds that are created will have aliasing distortion because they’ve been sampled at too low of a rate – resulting in “buzzing” or other unwanted noise being heard instead.

How to de-ess your vocal with an EQ?

De-essing is an often overlooked, but incredibly important aspect of the mixing process. Our ears are sensitive to 5kHz and above, where sibilance lies. Furthermore, in English at least -sibilant sounds- which include “S” or “Z” – especially when singing –are common and aggressive.

We could use a de-esser plugin that works by compressing a narrowband of sibilance-based frequencies, or we can make quick work in the EQ. If you have access to an EQ with dynamic mode – and noticed some harshness around vowel sounds like ‘s’, oi,’f’-‘v’- create your own dynamics range for those particular vowels. Narrowing down the bandwidth will give us more accurate results when it comes time to reduce hisses on consonants as well!

How to make your vocal cut through a mix?

In the world of sound, vocal clarity is often found in very high frequencies. In this range (2kHz and above), a lot of what makes up your voice’s character can be heard clearly. So if you find that when singing over instrumentation it’s hard to balance out both sounds, try boosting 2khz using a bell filter with medium-to-relaxed Q value for better results!

The sound of an instrument can drastically change depending on the quality setting, so it’s important to experiment with different settings. A sharper Q will provide a more precise sound while using 1.414 is better for natural sounds since that creates about one octave of bandwidth for frequencies between 200Hz and 5000 Hz (pitches). Listen intently as you move the bell filter up and down the spectrum until you find just the right spot for your vocalist in a particular mix! Amplifying by 2dB should be enough but avoid any amplification over 4dB because that causes distortion which might not have been there before due to how compressed things are – we want clean mixes without unwanted artifacts ruining our music!


How to make your vocal more intelligible?

It’s often the low-mids of a vocal that make your vocals sound unintelligible. These frequencies have loud amplitudes, so they easily mask quieter higher frequency sounds right above them!In order to tailor a vocal mix, it is best practice to attenuate any frequencies that may be obscuring the vocals. To do this effectively, find out what frequency range you want to be filtered and use an EQ with bell filter settings in 500Hz increments around those areas until you’ve found one suitable for your needs. For example, 700hz will help clear nasal singing while 300 Hz can maintain power without being overpowering if someone sings lower than average tones